Ex RF 96 ST SW915

Ex Wireless universal transmitter
Material number: 1314672
  • Ex zone 1 and 21
  • sWave® wireless technology
  • Power supply by ex-proof Lithium battery (exchange inside Ex areas possible)
  • Thermoplastic enclosure
  • Mounting details to EN 50047
  • Plug-in connector M12
  • No wiring and pipe laying required
  • Easy programming of receiver
  • Output signal can be individually configurated at the receiver
Notes
  • The Ex RF 96 ST may be used in combination with an Ex wireless inductive sensor Ex RF IS
  • Connection of external switching contacts only on request and only after evaluation by steute!
In stock
Contact

Technical data

Applied standards EN 60947-5-1, EN 61000-6-2, EN 61000-6-3, EN 301 489-1, EN 301 489-3, EN 300 220-1, EN 300 220-2, EN 60079-0, EN 60079-11
Enclosure thermoplastic, glass-fibre reinforced, impact resistant, self-extinguishing UL 94 V-0
Tightening torque M4 enclosure mounting screw: max 1.2 Nm
M2.5 cover screws: approx. 0.45 Nm
Degree of protection IP 20 to IEC/EN 60079-11,
IP 67 to IEC/EN 60529
Protocol sWave®
Frequency 915 MHz (USA, Canada and Mexico)
Transmission power < 25 mW
Data rate 66 kbps
Channel bandwidth 550 kHz
Voltage supply Ex approved and certified batteries, manufacturer steute, Ex RF Bat 3,6 V/2,1 Ah, mat. no. 1381655, BVS 18 ATEX E 035 X, IECEx BVS 18.0056X
System Li/SOCl2
Nominal voltage 3.6 V
Nominal capacity 2.1 Ah with integrated protective circuit
Battery life depending on the switching frequency
1 s approx. 500 days,
10 s approx. 1000 days,
100 s approx. 1100 days
Connection Plug-in connector M12 x 1, 4-pole
Ambient temperature –20 °C … +60 °C
Switching frequency max. 5 Hz
Standby current 215 µA (incl. sensor)
Wireless range max. 450 m outside,
max. 40 m inside
Actuating time min. 80 ms
Note Status signal adjustable via jumper, no, 10 s, 100 s, 1000 s, 10000 s
Delivery state: jumper position without status signal
Transmission of battery voltage and switching condition
Ex marking II 2G Ex ib IIC T4 Gb,
II 2D Ex ib IIIC T135 °C Db
IECEx Ex ib IIC T4 Gb,
Ex ib IIIC T135 °C Db
Approvals BVS 19 ATEX E 009 X
IECEx BVS 19.0040X
Weight 114 g

External switch contact

Sensors

Plug-in configuration

Colour coding only valid for
Coupling 4-poles mat. no. 1215497 and
Coupling 4-poles mat. no. 1262873


Accessories

Wireless receiver
RF Rx SW915-TCP/IP V2
  • sWave® wireless technology
  • Communication via UDP or TCP/IP (Server or Client - Mode)
  • Webserver based Setup
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of operating state
  • SMA reverse plug-in connector for external antenna
Wireless receiver / repeater
RF RxT SW915-USB
  • Different operating modes
  • USB-Standard Receiver Mode
  • USB Gateway Mode
  • Sniffer Mode
  • Repeater (1-Level and 2-Level Repeater Mode)
  • Virtual COM Port driver for Microsoft Windows, Linux, Apple Mac
Wireless receiver
RF Rx SW915-1W 24 VAC/DC
  • sWave® wireless technology
  • 1 potential-free relay output
  • 1 change-over contact, max. 6 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-2W-RS232 24 VAC/DC
  • sWave® wireless technology
  • 2 potential-free relay outputs
  • 2 change-over contacts, max. 6 A
  • RS 232 interface
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4W 24 VAC/DC
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 change-over contacts
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4S 24VDC - SET
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
Wireless receiver
RF Rx SW915-4S 24VDC Power-down-function
  • sWave® wireless technology
  • 4 potential-free relay outputs
  • 4 NO contacts, max. 3 A
  • Transmitter/receiver assignment by teaching mode
  • LEDs for indication of switching state
  • SMA reverse plug-in connector for external antenna
  • Power-down-function (saves the last signal status from the relay output, if the power supply of the receiver box is interrupted)
Wireless repeater
RF RxT SW915-1K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • SMA reverse plug-in connector for external antenna
Wireless repeater
RF RxT SW915-2K
  • sWave® wireless technology
  • LEDs for indication of operating state
  • 1-level repeater: for the signal gain between transmitter and receiver
  • 2-level repeater: for the signal gain of one 1-level repeater
  • SMA reverse plug-in connector for external antenna
Power supply 24V DC
  • Push-in terminals
RF magnet antenna 5dBi R-SMA plug-in connector straight 3.6 m
  • RF magnet antenna with straight R-SMA plug-in connector without ferrite core
  • Suitable for SW915 and SW917
  • Cable length 3.6 m
Field strength testing tool swView 915 MHz
  • Only suitable for sWave® 915 MHz wireless technology
  • Mobile field strength indicator for link range testing
  • To measure and indicate the electrical field strength
  • The batteries are included in delivery
  • Several functions can be selected: Scan-Mode, Repeat-Mode, Rescan-Mode, Radio-Link