ZS 92 S -40°C ... +85°C IP66/67 Extreme

  • Temperature resistant from -40 °C to +85 °C
  • High degree of protection IP 66 / IP 67 / IP 69
  • Corrosion-resistant aluminium enclosure
  • Screws made of stainless steel
  • Wire length up to 2 x 100 m
  • Release by lever
  • F = Reset lever at the front side
  • B = Reset lever at the back side
  • Back and base mounting possible
  • Wire pull and breakage detection
  • Version with Si-Bus available on request

Videos

Installation of emergency pull-wire switch ZS 92 S

Technical data

Applied standards EN 60947-5-1, EN 60947-5-5, EN ISO 13850, EN ISO 13849-1, EN 620:2011-5.7.2.9, AS 1755-2000-2.7.9.1, AS/NZS 4024.3610:2015-2.10.6.2
Enclosure aluminium die-cast, corrosion-resistant, powder-coated, passivated, impact resistant, anthracite grey, similar to RAL 7016
Cover aluminium die-cast, corrosion-resistant, powder-coated, passivated, impact resistant, signal yellow, similar to RAL 1003
Actuating lever aluminium die-cast, corrosion-resistant, powder-coated, passivated, impact resistant, signal red, similar to RAL 3001
Reset lever aluminium die-cast, corrosion-resistant, powder-coated, passivated, impact resistant, sky blue, similar to RAL 5015
Screws stainless steel
Tightening torque cover screws: max. 2.5 Nm
actuator screws: max. 6 Nm
Degree of protection IP 66/67/69 to IEC/EN 60529
B10d (10 % load) 100 000
TM max. 20 years
Contact material silver, with Si-Bus: silver, gold-plated
Switching system snap action, positive break NC contacts
Switching elements 2 NC/2 NO or 3 NC/1 NO contact, type Zb;
Si-Bus: 2 NC contacts, type Zb 
Connection screw connection terminals; with Si-Bus: screw connection terminals, basic strip to connect Dupline Safe input module with connector (see accessories)
Cable cross-section min. 0.5 mm², max. 2.5 mm² (incl. conductor ferrules)
Cable entry 2 x M25 x 1.5
Rated impulse withstand voltage Uimp 6 kV; with Si-Bus: 4 kV
Rated insulation voltage Ui 400 V; with Si-Bus: 250 V
Conventional thermal current Ithe 6 A
Conditional short-circuit current 1100 A
Rated operating current/voltage Ie/Ue 6 A/400 VAC; with Si-Bus: 6 A/250 VAC
Utilisation category AC-15
Short-circuit protection 6 A gG/gN fuse
Mechanical life > 50 000 operations
Max. wire length 2 x 100 m
Ambient temperature –40 °C … +85 ºC
Si-Bus: with Si-Bus –40°C ... +70°C; without Si-Bus –40°C ... +85°C
Degree of pollution 3
Actuating force actuating lever approx. 30 N; reset lever approx. 40 N
Indicator lamp as option
Pressure equalization element as option
Approvals

Ordering details

Reset lever at the front side

Type   Material no.  
Type    Material no.   
ZS 92 S 22 VD F -40°C ... +85°C IP66/67 Extreme stock type Standard versions, in stock or available at short notice 1457232
Type    Material no.   
ZS 92 S 13 VD F -40°C ... +85°C IP66/67 Extreme 1446778
Type    Material no.   
ZS 92 S 02 VD Si-Bus F -40°C ... +70°C IP66/67 Extreme stock type Standard versions, in stock or available at short notice 1364521
If you cannot find the version you require, just ask us! Our product portfolio to date has included many customised switchgear variants.

Reset lever at the back side

Type   Material no.  
Type    Material no.   
ZS 92 S 22 VD B -40°C ... +85°C IP66/67 Extreme stock type Standard versions, in stock or available at short notice 1456669
Type    Material no.   
ZS 92 S 02 VD Si-Bus B -40°C ... +70°C IP66/67 Extreme 1363023
If you cannot find the version you require, just ask us! Our product portfolio to date has included many customised switchgear variants.

Reset lever at the front side + indicator lamp

Type   Material no.  
Type    Material no.   
ZS 92 S 22 VD L F -40°C ... +80°C IP66/67 Extreme stock type Standard versions, in stock or available at short notice 1277146
If you cannot find the version you require, just ask us! Our product portfolio to date has included many customised switchgear variants.

Accessories

Safety Input Module GS 7510 2192
  • Safety input module for installation inside emergency pull-wire switch ZS 92 S
  • Safety approved according to IEC/EN 61508-SIL3, IEC/EN 62061-SIL3 and ISO/EN 13849-1 PL e
  • c UL us approval
  • Single input for potential-free contacts
  • Uses two Dupline® channels
  • Bus-powered
Safety Input Module GS 7510 2192-1
  • Safety input module for installation inside emergency pull-wire switch ZS 92 S
  • Safety approved according to IEC/EN 61508-SIL3, IEC/EN 62061-SIL3 and ISO/EN 13849-1 PL e
  • c UL us approval
  • Single input for potential-free contacts
  • Uses two Dupline® channels
  • Bus-powered
  • Incl. 8 pin multi connector
Compensation spring ZS 90/91/92 S
  • For emergency pull-wire switches series ZS 90 S, ZS 91 S and ZS 92 S
  • With travel limitation
  • Adaption of length expansions caused by changes in temperature
  • Version consisting of: stainless steel chain, 2 carabiner galvanized and tension spring (1.4310)
Compensation spring ZS 90/91/92 S stainless steel
  • For emergency pull-wire switches series ZS 90 S, ZS 91 S and ZS 92 S
  • With travel limitation
  • Adaption of length expansions caused by changes in temperature
  • Version consisting of: stainless steel chain, 2 carabiner A4 (1.4401) and tension spring (1.4310)
Cable Tensioner System TS 65
  • Only one tool
  • Injury-free
  • Ergonomically designed
  • Easy to adjust
  • Non-slip
  • Time-saving
Tensioner M6
  • For precise adjustment of pull-wire pre-stress
  • According to DIN 1480
  • Adjustable from 145 mm to 225 mm
Tensioner M8 stainless steel
  • For precise adjustment of pull-wire pre-stress
  • According to DIN 1480
  • Made of stainless steel
  • Adjustable from 160 mm to 255 mm
Pull-wire Ø 5 mm per metre
  • Steel core Ø 3 mm with red PVC sheath
  • Total diameter 5 mm
  • Ordering unit: per meter
Pull-wire stainless steel Ø 5 mm per metre
  • Stainless steel core Ø 3 mm with red PVC sheath
  • Total diameter 5 mm
  • Ordering unit: per meter
Complete pull-wire set, 5 m
  • Complete pull-wire set consisting of:
    5 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 10 m
  • Complete pull-wire set consisting of:
    10 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 15 m
  • Complete pull-wire set consisting of:
    15 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 20 m
  • Complete pull-wire set consisting of:
    20 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 25 m
  • Complete pull-wire set consisting of:
    25 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 30 m
  • Complete pull-wire set consisting of:
    30 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 40 m
  • Complete pull-wire set consisting of:
    40 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Complete pull-wire set, 50 m
  • Complete pull-wire set consisting of:
    50 m pull-wire Ø 3 mm with 2 mm PVC sheath,
    2 wire clamps DIN 741,
    1 wire thimble DIN 65457,
    1 eye bolt DIN 444 and
    1 Duplex wire clamp
Pulley stainless steel
  • To guide the pull-wire where the path is not a straight line
  • Roller: polyamide
Wire clamp 3 mm
  • For pull-wire with steel core Ø 3 mm
Wire clamp 3 mm stainless steel
  • For pull-wire with steel core Ø 3 mm
  • Stainless steel
Duplex wire clamp
  • For pull-wire with steel core Ø 3 mm
Egg-shaped wire clamp
  • For pull-wire with steel core Ø 3 mm
Wire thimble RW 4
  • According to DIN 65457-35 Z
  • For pull-wire with steel core Ø 4 mm
  • Galvanized
  • Tip 6 mm open
Wire thimble RW 3 stainless steel
  • For pull-wire with steel core Ø 3 mm
  • Stainless steel 1.4401
Eye bolt M8 x 70 with nut
  • According to DIN 444
  • 70 mm length referring to eye centre, 25 mm thread length,
    M8 x 1.25 thread
Eye bolt BM8 x 70 with nut, stainless steel
  • According to DIN 444
  • 70 mm length referring to eye centre, 25 mm thread length,
    M8 x 1.25 thread
  • Stainless steel
Eye bolt BM10 x 40 with nut
  • According to DIN 444
  • 40 mm length referring to eye centre, 25 mm thread length,
    M10 x 1.5 thread
Eye bolt open M10 x 120 with 2 nuts
  • 120 mm length, 70 mm thread length
  • M10 thread
  • Galvanized steel
  • 2 hexagon nuts are provided
Indicator lamp LED 24 VAC DC
  • Calotte red transparent
  • M20 x 1.5
  • 24 VAC/DC
Indicator lamp Multi-LED RD 24 VDC
  • Lamp cap red
  • M20 x 1.5
  • 24 VDC
Indicator lamp Multi-LED RD 115 VAC
  • Lamp cap red
  • M20 x 1.5
  • 115 VAC
Indicator lamp Multi-LED RD 230 VAC
  • Lamp cap red
  • M20 x 1.5
  • 230 VAC